Page 1 of 1
How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 10, 2015 3:32 am
by gengkai
Greetings.
I want to ask on how to enable the IPv6 service using Softether VPN as I am sure that Softether support IPv6. Do I need to create DHCP for the server to distribute the IPv6 address? Can we allocated speed to the client from the server?
Thank you.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 10, 2015 9:48 am
by kh_tsang
If you are using bridge to your LAN, you only need to configure your lan to support IPv6, no need configuration on the Virtual Hub.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 10, 2015 10:06 am
by kh_tsang
There is one more method. To setup tap_device for each virtual hub, then disable the virtual NAT and use linux routing softwares and dhcp servers.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 10, 2015 1:30 pm
by gengkai
Thanks kh_tsang for your reply.
I am using Windows Server 2008 for my server hosted by ramnode. Probably, Linux not applicable for Windows.
Is there anything that I need to configure at the VPN Server?
Thank you.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 10, 2015 2:35 pm
by kh_tsang
Then you can try to use the vpn client to connect to the server itself to make an adapter instead of adding the tap device.
Set a static IP on the vpn adapter and tick no adjustment of routing table in the vpn connection settings.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Wed Feb 11, 2015 5:08 am
by gengkai
Hello kh_tsang.
I did try your method and it works. But the things that I want is the client can have the IPv6 address allocated to the client automatically rather than client enter the IPv6 address manually at the VPN adapter.
Here's the result after I try using your method.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Thu Feb 12, 2015 3:57 am
by kh_tsang
You can try to install DHCP server on your Windows Server, the one from Microsoft, and assign addresses on the vpn adapter using it.
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Tue Feb 14, 2017 2:43 pm
by vitaliksys
gengkai wrote:
> Hello kh_tsang.
>
> I did try your method and it works. But the things that I want is the
> client can have the IPv6 address allocated to the client automatically
> rather than client enter the IPv6 address manually at the VPN adapter.
>
> Here's the result after I try using your method.
can you help with setup ? please provide a comprehensive tutorial or contact me via skype - zosea.frosea
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Mon May 14, 2018 1:35 pm
by sara1112
Hello kh_tsang,
I want to also configure softether ipv4 over ipv6.. I hope you did already this step , shall you share your stop what you did please
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Fri Jun 01, 2018 4:54 am
by thisjun
Special configuration isn't required for IPv4 over IPv6.
What problem do you have?
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Sun Jun 03, 2018 8:42 am
by sara1112
HI
i don't have idea about ipv6 i have configured ipv4 using secure NAT I want to configure ipv6
Re: How Enable IPv6 Service and Allocated Speed To Client
Posted: Thu Jun 14, 2018 8:28 am
by thisjun
SecureNAT handles inside network.
If you want to configure IPv4 over IPv6, SecureNAT isn't needed to handle IPv6.